Skip to main content

H.H. Scott 377B Receiver

I thought I would never buy another vintage receiver, until this HH Scott 337B popped on the market. It was partially recapped and the work was done by a fellow AKer. You can see his work and his ramblings on audiokarma here: HH Scott 377B

I've never heard an American made HH Scott before. While the Japanese made ones sounded nice, they all sounded much like other Japanese made stuff in the late 70s. I was curious about the American made ones. I had an inkling that because it was made in the early 1970s it would be very warm sounding as a lot of early solid state gear replicated the sound of tube amps of the era before.

My suspicions were correct, the HH Scott 377B definitely is on the warmer side of things. Its very nice, very "full/robust" sounding. Definitely a lot more robust sounding over the Pioneer SX-636 I had previously. It has a certain tube characteristic with an emphasis on the more midrange, which is nice. If matched with a more "brighter" sounding speakers to "balance" things out, I think it will sound fantastic. If you like early 70s gear, you will like this Scott. 

The tuner is sufficient, an antenna would work best (like with all tuners) and sounds alright.

Overall, the condition is good. Lamps were replaced and while it seems one of the meter light isn't as bright as the other, that is due to the pigment on the diffuser, no the bulb itself. I think the overall build quality is good, probably similar to many Japanese makes of the time. However, there are a few things I am not a huge fan of 1) the particle board and vinyl wrapped case (some peeling so it can be either be replaced or re-veneered), 2) the second set of speaker binding post are a set of RCA plugs and 3) there are only 3 indicator lamps - FM, AM and "Stereo," no phono or auxiliary light. Nitpicking: the speaker spade connectors are very narrows so I couldn't even use my banana to spade adapter - so I keep some wire attached for ease of plugging them in.

Certainly, the cost saving measures were indicative to keep up with the Japanese manufacturers. But, where quality was needed, it was there.

It's pretty powerful at 40wpc considering this was the middle of the HH Scott trio of the 357B/377B/387B series. It's heavy too! Roughly 26lbs. 

There is not a lot of information about these series of receivers however, they are well made (heavy) and have a very nice mid-century design. The face of the 377B is beveled. Looks great!

Specification according to vintageshifi.com:

American manufacturing
Tuning range: AM FM
FM: 88/109 Mhz
MW: 535/1620 Khz
Usable Sensitivity FM IHF: 1.9 µV
Capture Ratio: 2.5
Selectivity: 35dB
Stereo Separation: 30dB
Tape Output: 0.5v
Power output: 2X40w/8 ohms
Frequency response: 15Hz/20kHz
Total harmonic distortion: 0.5%
Input sensitivity Phono: 3, 6 mV
Signal/noise ratio: 75dB
Dimensions: 17"1/2 X 5"1/2 x 13"1/2
Dimensions: 444 x 140 x 342 mm
Weight: 12,7 KG - 28 Lbs
1972 Price:$ 319,90








Popular posts from this blog

Yamaha YP-66 Turntable

The rosewood vinyl wrapped twin sibling of the Yamaha YP-221, they are the exactly the same other than the colour of the plinth and instead of silver plastic bits on the YP-221 the YP-66 has black bits. This is your typical belt drive turntable of the mid to late 70s.  It's a 2-speed with automatic return (semi-automatic).  It's a nice entry level turntable with all the decent built quality that you find on majority of the Japanese made tables of that era.  It has a good sized motor and a decent weight.  Yamaha tables are like Sony tables, they always have decent quality components and they always look nice to the eyes.  The slight smoked dustcover and the rosewood plinth makes it quite unique to look at. Sadly, the antiskate weight on our isn't original.  It was missing when we got it.  After a bit of research we found the appropriate weight and found an appropriate weight to retrofit into our table.  We found a nice brass weight to fit with the design.  And, as usual,
Read more

Energy Encore 2 Speakers

My family were the original owners of these speakers. We actually had the entire Energy Encore 5.1 surround set, minus the integrated stands. Slowly, the rear speakers were sold. I kept the subwoofer to use with my sound bar, and the center channel broke. All that remained were these little guys sitting on the same shelving unit for the past 15ish years. I used them for a bit for my computer setup but, opted to use my Mirage Omni 350 instead. While these are considered "big box store" speakers, they are still great little speakers. These were made in Canada. Used their hyperdome aluminum tweeter that made Energy famous from the Pro22 days (thank you Burhoe!). A super nice black piano finish and sealed box, with a 4" long throw woofer. Some Specifications that I took from the web: System Type: Magnetically shielded acoustic suspension satellite Tweeter: 1" (28mm) Aluminum dome with cloth suspension Woofers: 4" (112mm) Multi-laminated aluminum polycarbonate c
Read more

Micro Seiki MR-622 Turntable

This is one of my greatest prize possessions, well for turntables.  The Micro Seiki MR-622 is a fabulous turntable, and definitely has been one of my favourite tables that I had the pleasure of owning. Everything about this turntable screams quality.  Even the 45rpm adapter seemed to be milled aluminum.  It has adjustable feet, a side pocket for accessories , a nice heavy die cast platter and even the top part of the plinth is cast.  All wrapped in a beautiful smoked dustcover and real wood sides. The Micro Seiki MR-622 is a fully manual, 2-speed, direct drive turntable.  This means, it's low maintenance and high reliability as there is less moving parts within the turntable.  It's just a huge motor, speed controls and Micro Seiki MA-202 tone arm, placed in a overly built plinth just like what one would expect from Micro Seiki. The MA-202 tone arm is a S-shaped tone arm with excellent tracking ability.  It has an adjustable counterweight and the tone arm pipe is filled w
Read more